- #Slmgr is not recognized as internal or external serial number
- #Slmgr is not recognized as internal or external serial
- #Slmgr is not recognized as internal or external driver
- #Slmgr is not recognized as internal or external manual
- #Slmgr is not recognized as internal or external code
Select a lower frequency from the drop-down list. Trace Selected SWO Clock is not supported Selected SWO clock frequency is not supported (too Could not stop ARM device The debugger tries to stop the target.
#Slmgr is not recognized as internal or external code
Target's Flash was not programmed with the code being debugged.ĭownload the program to Flash. Then the code in the target isĬompared against the load image. Appears when the option Verify Code Download is enabled and whenĪ debugging session is started. Memory Mismatch Memory mismatch detected while downloading the code Target problems: debug block not powered and clocked properly. Device could not be powered up Debug block on the device could not be powered.ĭebug block on the target is not working properly. In someĬases, the target's debug block not functioning properly raises The target, or through a stop/step command while debugging. This attemptĬan be made after initializing the connection, or while resetting Could not stop Cortex-M device The debugger tries to stop the target. Mainly causedīy target problems: debug block not powered or clocked properly.Īvoid Deep-Sleep modes while debugging. The target debug interface is not working properly. Cannot enter Debug Mode Debug Interface on the target cannot be accessed.
#Slmgr is not recognized as internal or external driver
This message can also be displayed due to the target'sĭebug block being improperly powered or clocked (for example inĬlock frequency in the Target Driver Setup - Debugĭialog might help. Avoid accessing invalid memory areas on the target Debug Cannot access Memory Memory on the target cannot be accessed by theĭebugger. Target: debug block not powered or clocked properly. Target SWD interface is not working properly.
#Slmgr is not recognized as internal or external serial
SWD Communication Failure Serial Wire Debug communication is corrupted. Enable the SWJ switch in theĪdapter section of the Target Driver Setup - Debugĭialog. Device is not connected, or not powered, or the debug Serial Wire Debug No Cortex-M SW Device Found No Cortex-M processor-based device detected (using
#Slmgr is not recognized as internal or external manual
Check the connections, or try a manual RESET. No ARM Device found in JTAG chain No ARM7/ARM9 processor-based device detected (using The chain (maximum 64 devices are allowed), or the JTAGĬommunication is corrupted and it behaves as if too many devicesĪre present. Too Many JTAG Devices in Chain Either too many JTAG devices have been detected in Target notĬonnected or not powered, or JTAG interface is not working. No JTAG Devices Found No JTAG device has been detected. Section of the Target Driver Setup - Debug dialog. Enable the SWJ switch in the ULINK USB-JTAG/SWD Adapter Device is not connected, not powered, or the debug interface No Cortex-M Device found in JTAG chain No Cortex-M processor-based device detected (using Requirements, or the JTAG chain is not configured properly. JTAG Device Chain Error Devices on the JTAG chain do not meet the Mainly caused by the target:ĭebug block not powered or clocked properly. JTAG JTAG Communication Failure JTAG communication is corrupted. Macro Sequence too long Internal driver error. Macro Sequence Error Internal driver error. Macro Execution Error Internal driver error. DR Communication Sequence Error Internal driver error. ULINK2/ME from the USB port and plug it back in. USB Communication Failure USB communication is lost or corrupted. ULINK2/ME Macro Buffer overflow Internal driver error. Unplug ULINK2/MEįrom the USB port and plug it back in. ULINK2/ME Communication Timeout Communication is lost or corrupted. No drop-down list in the Target Driver Setup dialog. Occurs when more ULINK2/ME adapters have been detected,īut none has been selected. No ULINK2/ME is selected No ULINK2/ME adapter has been selected forĭebugging. The USB port, or the USB driver is not installed properly, or
![slmgr is not recognized as internal or external slmgr is not recognized as internal or external](https://i.ytimg.com/vi/qcLeWth1Rdw/mqdefault.jpg)
No ULINK2/ME device found No ULINK2/ME detected. Unplug ULINK2/ME from the USB port and plug it back in.
![slmgr is not recognized as internal or external slmgr is not recognized as internal or external](https://www.asavvyweb.com/wp-content/uploads/2020/11/SLMGR-is-not-recognized-in-windows-10-internal-or-external-command-min-300x145.jpg)
#Slmgr is not recognized as internal or external serial number
Cannot read ULINK2/ME Firmware serial number Communication is lost or ULINK2/ME is not working. Cannot read ULINK2/ME Firmware version number Communication is lost or ULINK2/ME is not working. Firmware isĬorrupted or cannot be downloaded due to hardware problems. ULINK2/ME Firmware Download Failed ULINK2/ME firmware cannot be downloaded. If you are experiencing difficulties, contact our support group. The messages are sorted in groups to identify the error cause easily. This list identifies errors that might occur when using ULINK2/ME.